Brass Moulding Inserts
Brass inserts Brass Moulding Inserts Brass Plastic
Moulding Inserts Brass Plastic Molding inserts Brass Injection
Moulding Inserts Brass Injection Molding Inserts Brass roto molding
Roto moulding inserts Brass inserts for cold moulding Hot insert
molding
Brass Moulding Inserts Special
Features :
-
Threads as per International Go & Not Go
Standards. Brass Stainless Steel Nuts Moulding inserts molding
nuts
-
Deep Groove for maximum Pull Out Resistance.
-
Inner Diameter (I/D) after Threads with very close
tolerance to prevent unnecessary flush to enter into the inserts.
-
Knurling Available :
-
Diamond
-
Straight
-
Unidirectional
-
Both blind and through inserts are available with
no minimum Qty.
Special Brass inserts Moulding
Inserts Molding Brass inserts Available
We shall be pleased to develop
Non-Standard Brass inserts components nuts screws studs fixings
wood screws machine screws fasteners as per specific requirements.
Materials
Brass to BS 2874 / 2872
Finish
Brass natural, Electro-Tinned, Nickel etc.
Threads
ISO Metric, BSW, BA, BSF, UNC, UNF UNEF etc.
Threads: 2mm 3mm 4mm 5mm 6mm 8mm
10mm 12mm 16mm 20mm 25mm 32mm 1/8" 5/32" 3/16" 1/4" 5/16" 3/8" 1/2"
5/8" 3/4" 1" 11/8" 11/4" 11/2" 13/4" 2"
BRASS STRAIGHT KNURLED MOULDING
INSERTS
Features: They are one one
thro' hole Brass inserts. They can be potted in or moulded. A
straight knurl offers better torque out capabilities.
Sizes: from 2mm -10mm
BRASS HELICAL MOULDING INSERTS
MOLDING NUTS
Features: They are compact
inserts suitable for insertion in all types of plastics and can be
used with hot plastic Moulding and cold plastic molding . Inserts
are best suitable for electrical moulded box application..
Sizes: from 2mm -12mm and 1/8"
- 1/2"
Brass Inserts for CPVC and UPVC
Drainage and Sewerage fitting Moulding
Features: These Brass inserts
are used for UPVC moulding CPVC molding for dewerage and daringae
pipe fittings elbows and Pipe couplings .
Sizes: from 1/4"mm -3/4" mm
BRASS INSERTS FOR WOOD AND PLASTIC
Features: These Brass inserts
are push fit type and are used with Wood and plastic moulding. .
Sizes: from 1/4"mm -3/4" mm
BRASS SELF TAPPING INSERTS
Features: These inserts are
suitable for installation with wide range of thermoplastics and are
sued where high pull out torque is required.
Sizes: from 1/4"mm -3/4" mm
BRASS KNURLED MOULDING SCREWS
Features: These screws are used
for moulding of Nylon spacers and pillars.
Sizes: from 2mm-10mm and
1/8"-3/8"
Brass Material used for Brass Moulding Inserts: CZ 115 c377, c380, cz122, en 12165, cw617n, cw612n, cuzn40pb2,
cuzn39pb2, BS 2874 - CZ 121 Pb3 , UNS C36000 CDA 360 DZR, Brass BS
2874 - CZ 131 CW 614 N.
|